Force-V4

Hello , as per the title, coming home after a ride yesterday , my Pgm F1 light came on . This afternoon I've been trying to work out the problem . With the seat and bodywork off using the 'diagnostic port ' the Pgm light is showing 7 blinks - so far so good . I've them followed the steps in the manu...

Thanks again Larry . When I get the time and money I intend to go to a dyno place and do a before and after 3 wire trick - just to measure the difference , on the same dyno on the same day . I've also got a 2nd jap ( restricted ) spec ECU which I intend to do the same with. Anyone else got a tips or...

Thanks Larry . 'Adding lightness' - to quote Colin Chapman is an idea , as I have a set of magnesium wheels . However the shocking state of the roads in the UK has put me off using them ,so I'm back to the standard wheel set up - although I do have a VFR 17" front wheel. Do you know if the 3 wi...

Thanks for the reply Larry . Do you know if your A/F ratio is optimised , was it ever measured on the dyno when you got your power figures ?
Is that for your tuning , or do you plan to do any more ?

Mike

Hello , I know that 45's are difficult to tune without going down the full HRC route . I've got a full exhaust , the flapper cut out of the front of my airbox and a power commander hard wired into my loom to get the A/F ratio as good as it can be. Is there anything else that I can do to get more pow...

Wow , that's quite a stash you have there . Just out of interest do your new injectors have any dots of colour on them ? . I've taken a picture of mine , and they have a white and green dot of paint on the body , and a blue dot by the electrical connector . I've no idea if this had been done by Hond...

Hello , Well I managed to buy what might be the last NOS injectors in existence as one of my injectors will not clean up 100% . I just wanted to check that all RC45 injectors were the same , as I thought that they were . They came in a box with the Honda part number 06164-MW4-000. I'll copy below wh...

Hello , I'm still having problems with my cold start, as the ECU is not telling the injectors to give more fuel from cold . I've tried another ECU , but I've still got the same problem. I've just noticed that when I switch the engine off , the PGM light very briefly flickers on - can anyone confirm ...

Hello , It time for a new chain & sprockets on my RC30 . Does anyone have any recommendations as to which make is best ? , what have you fitted ?
Thanks
Mike .

Hello , I know it's a long shot , but has anyone got a RC45 ECU or set of injectors in a stash that they want to sell ?
Thanks
Mike .

Hello , Does anyone know if the fuel injectors are still available from Honda ? , as having a quick look , they appear to be NLA . Mine are off for cleaning and despite 4 or 5 attempts one of them is not atomising as good as the other three . It's just about OK but not great and could be better . If...

Hello , From a previous post of mine , I found that the front of my airbox had been cut away just to leave a hole , https://i.imgur.com/eeEEbWE.jpg I managed to buy a compete airbox off of Ebay , so with high hopes of a better torque cure off I went back to the dyno shop . In a effort to try and be ...

Hello , Just trying to find a slight pesky coolant leak on my 45 , and it seems to be coming from the top rad house . Anyway , I was trying to see where the hose goes into the head , so I took the tank off and found this on the airbox lid , https://i.imgur.com/eeEEbWE.jpg So it's just a hole , which...

Sold

Mike

Hello , Could anyone help me with getting a left and right standard front wheel spacers ? I've currently got a dymag front fitted but fancy going back to the standard 6 spoke look . I've got a NC30 front wheel ready to fit , but I've found out that the standard spacers are no longer available from H...